Cookies Policy
The website need some cookies and similar means to function. If you permit us, we will use those means to collect data on your visits for aggregated statistics to improve our service. Find out More
Accept Reject
  • Menu
Publications

Publications by Luís Carlos Coelho

2017

Low temperature oxidation in air of iron thin films monitored with long period fiber gratings

Authors
Coelho, L; Santos, JL; Jorge, PAS; de Almeida, JMM;

Publication
OPTICAL SENSORS 2017

Abstract
In this work an investigation of long period fiber gratings (LPFGs) over coated with iron (Fe) thin layers with different thicknesses and subjected to oxidation in air atmosphere under controlled temperature is presented. The formation of iron oxides was monitored in real time by following the optical features of the LPFG attenuation band. The morphology of the oxide layer was further analyzed by scanning electron microscope (SEM). Preliminary results show that iron coated LPFGs can be used as sensors for early warning of corrosion in projects where metal structures made of iron alloys are in contact with atmospheric air.

2013

Pressure Sensor based on an all-fiber Fabry-Perot interferometer for different gaseous environments

Authors
Silva, S; Coelho, L; Frazao, O;

Publication
FIFTH EUROPEAN WORKSHOP ON OPTICAL FIBRE SENSORS

Abstract
This work describes an all-fiber Fabry-Perot interferometer (FFPI) that is sensitive to gas pressure variations. The geometry of the air cavity consists on splicing a small section of silica rod with a large offset in between two singlemode fibers. It is shown that the FFPI sensor is sensitive to gas pressure variation and when submitted to different gaseous environments, namely carbon dioxide, nitrogen and oxygen, it presented different sensitivities of 6.2, 4.1 and 3.6 nm/MPa, respectively. This result is obtained due to refractive index difference between gases. The refractive index change on nitrogen environment by means of the gas pressure variation resulted in a sensitivity of 1526 nm/RIU. The response of the sensing device to temperature in air was also determined and a sensitivity of -14 pm/degrees C was attained.

2015

Real time monitoring oxidation of transition metals with long period fiber gratings

Authors
Coelho, L; Viegas, D; Santos, JL; de Almeida, JMM;

Publication
24TH INTERNATIONAL CONFERENCE ON OPTICAL FIBRE SENSORS

Abstract
In this paper real time monitoring of oxidation of transition metals using long period fiber gratings (LPFG) is performed for nickel, copper, titanium, chromium and zinc. A thin layer is deposited over the LPFG with physical process deposition and is annealed up to 700 degrees C in air with a small oven. The whole oxidation process can be monitored by tracking the LPFG features of the attenuation band which results in an abrupt change when the oxidation occurs depending on the metal sample. A preliminary study to optimize optical fiber sensors sensitivity allowing choosing the correct oxide layer in a specific application is presented.

2013

Sensing Structure based on Surface Plasmonic Resonance in Single Mode Optical Fibers Chemically Etched

Authors
Coelho, L; Almeida, JM; Santos, JL; Ferreira, RAS; Andre, PS; Viegas, D;

Publication
FIFTH EUROPEAN WORKSHOP ON OPTICAL FIBRE SENSORS

Abstract
Many optical systems based on Surface Plasmon Resonance (SPR) have been developed for work as refractometers, chemical sensors or even for measure the thickness of metal and dielectric thin films. These kinds of systems are usually large, expensive and cannot be used for remote sensing. Optical fiber sensors based on SPR has been widely studied for the last 20 years with several configurations mostly using multimode optical fibers with large cores and plastic claddings. Sensors based on SPR present very high sensitivity to refractive index variations when compared to the traditional refractive index sensors. Here we propose a SPR sensor based in a single mode fiber. The fiber end is chemically etched by emersion in a 48% hydrofluoric acid solution, resulting a single mode fiber with the cladding removed in a small section. A resonance dip around 1580 nm was attained in good agreement with the simulation scenario that takes into account the real characteristics of the fiber.

2018

Temperature Compensated Strain Sensor Based on Long-Period Gratings and Microspheres

Authors
Ascorbe, J; Coelho, L; Santos, JL; Frazao, O; Corres, JM;

Publication
IEEE PHOTONICS TECHNOLOGY LETTERS

Abstract
In this letter, we present a new structure composed by a long-period grating (LPG) and a microsphere in series, which works as a modal interferometer besides allowing the mode coupled to the cladding to be coupled back to the core. The LPG was written by the electric arc technique and the microsphere was fabricated using a splicing machine. It is possible to use this new structure for simultaneous measurement of strain and temperature. It also allows one to obtain a temperature compensated strain sensor by using a proper data processing algorithm, which utilizes two distinct wavelengths for strain and temperature. Then, a strain sensitivity of 0.86 pm/mu epsilon and a reduced temperature sensitivity of 0.7 pm/degrees C were achieved.

2017

Phase-interrogated SPR sensing structures based on tapered and tip optrode optical fiber configurations with bimetallic layers

Authors
Moayyed, H; Leite, IT; Coelho, L; Santos, JL; Viegas, D;

Publication
MEASUREMENT SCIENCE AND TECHNOLOGY

Abstract
This work reports the theoretical investigation of optical fiber surface plasmon resonance sensors incorporating bimetallic layer combinations. Different metals like silver, gold, copper, and aluminum are considered to investigate the refractometric sensing properties of tapered and tip optrode phase-interrogated optical fiber plasmonic sensor structures. It is shown that the gold-silver combination, coupled to a tip optrode layout, is capable of maximizing the resolution and operation range of these sensing structures for environmental refractive index measurement.

  • 5
  • 26