Abstract
A large-core air-clad photonic crystal fiber-based sensing structure is described, which is sensitive to refractive index. The sensing head is based on multimodal interference, and relies on a single-mode/large-core air-clad photonic crystal fiber (PCF)/single-mode fiber configuration. Using two distinct large-core air-clad PCF geometries-one for refractive index measurement and the other for temperature compensation, it was possible to implement a sensing head sensitive to refractive index changes in water as induced by temperature variations. The results indicated the high sensitivity of this sensing head to refractive index variations of water, and a resolution of 3: 4 x 10(-5) refractive index units could be achieved. (C) 2011 Optical Society of America

Abstract
A high sensitivity Fabry-Perot (FP) strain sensor based on hollow-core ring photonic crystal fiber was investigated. A low-finesse FP cavity was fabricated by splicing a section of hollow-core ring photonic crystal fiber between two standard single mode fibers. The geometry presents a low cross section area of silica enabling to achieve high strain sensitivity. Strain measurements were performed by considering the FP cavity length in a range of 1000 mu m. The total length of the strain gauge at which strain was applied was also studied for a range of 900 mm. The FP cavity length variation highly influenced the strain sensitivity, and for a length of 13 mu m a sensitivity of 15.4 pm/mu epsilon was attained. Relatively to the strain gauge length, its dependence to strain sensitivity is low. Finally, the FP cavity presented residual temperature sensitivity (similar to 0.81 pm/degrees C). (C) 2012 Optical Society of America

Abstract
In this work, sensitivity to strain and temperature of a sensor relying on modal interferometry in hollow-core photonic crystal fibers is studied. The sensing structure is simply a piece of hollow-core fiber connected in both ends to standard single mode fiber. An interference pattern that is associated to the interference of light that propagates in the hollow core fundamental mode with light that propagates in other modes is observed. The phase of this interference pattern changes with the measurand interaction, which is the basis for considering this structure for sensing. The phase recovery is performed using a white light interferometric technique. Resolutions of +/- 1.4 mu epsilon and +/- 0.2 degrees C were achieved for strain and temperature, respectively. It was also found that the fiber structure is not sensitive to curvature. (C) 2009 Optical Society of America

Abstract
In this work an all-optical hot-wire flowmeter based on a silver coated fiber combining a long period grating and a fiber Bragg grating (FBG) structure is proposed. Light from a pump laser at 1480nm propagating down the fiber is coupled by the long period grating into the fiber cladding and is absorbed by the silver coating deposited on the fiber surface over the Bragg grating structure. This absorption acts like a hot wire raising the fiber temperature locally, which is effectively detected by the FBG resonance shift. The temperature increase depends on the flow speed of the surrounding air, which has the effect of cooling the fiber. It is demonstrated that the Bragg wavelength shift can be related to the flow speed. A flow speed resolution of 0.08m/s is achieved using this new configuration. (C) 2011 Optical Society of America

Abstract
A theoretical and experimental study of a new fiber loop mirror based on a "figure-of-eight" configuration, is reported. For the theoretical model, the Jones matrix analysis is analyzed. The configuration is tested as an interrogation system where the spectral response arises from the combination of the reference signal modulated by the sensor signal. The configuration is characterized in mechanical strain and presents a phase sensitivity of 8.2 mrad/mu epsilon.

Abstract
In this work, a novel high birefringent (HiBi) fiber loop mirror sensor based on a "figure-of-eight" constructed with a 3x3 fiber coupler, is presented. The "figure-of-eight" is formed by two fiber loop mirrors (FLM's) made by four of the six fiber arms of the 3x3 fiber coupler. The other two remaining fiber ports of the 3x3 coupler are used as input and output fibers of the compound sensor. The sensing head is located in the one of the FLM and it is formed by a spliced section of HiBi elliptical core fiber. The spectral response of this "figure-of-eight" configuration presents two interference optical signals that can be easily tuned by a polarization controller that is located in the other FLM, and which is made only of standard singlemode fiber from two arms of the 3x3 coupler. The sensor head was optically characterized both in temperature and strain, showing wavelength dependence sensitivities of -0.23 nm/degrees C and - 2.6 pm/mu epsilon, for temperature and strain, respectively. It is noticed that these sensitivities are practically the same for the two interference signals. Future work will explore the possibility to use the singlemode FLM to interrogate the sensor head made by HiBi fiber section, and providing elimination of phase fluctuations that can occur, increasing its potential for remote sensing applications.