Abstract
In this work, we analyze a remote optical sensor system based on Raman amplification, composed by one Long Period Grating (LPG) as a sensor head, separated by 50 km from the optical source, and the interrogation unit composed by two Fiber Bragg Gratings (FBGs) modulated by two Piezoelectrics Transductors (PZTs). Optical fiber sensor systems are typically limited to operate at distances of only few kilometers due to the attenuation effects and noise present in the optical fiber that adversely affects the performance of the sensor interrogation process. We present experimental and simulated results obtained in the context of the analysis of remote optical fiber sensors. The simulation models compute the Raman interaction between the pumps and the sensor signals and allow speeding up the analyses regarding the setup to be experimentally implemented in order to measure/monitor environmental temperature. Experimental results obtained in the implemented setup show that under Raman amplification the power ratio between the two central wavelengths of the FBGs has a linear relation with the change of the LPG resonance induced by environmental temperature.

Abstract
In this work. the LPG-assisted fibre Michelson modal interferometer is studied as a sensing structure to environmental refractive index, temperature and liquid level when coherence addressing and heterodyne interrogation are considered. The effects on measurand sensitivity of the order of the cladding mode excited by the LPG, of the degree c etching of the sensing fibre and of the fibre type used are investigated.

Abstract
Birefringence monitoring of a Hi-Bi fibre under chemical etching is conducted. The Hi-Bi fibre (a bow-tie type) was inserted in a fibre loop mirror and the optical spectral response was measured while chemical etching of the Hi-Bi fibre was taking place. The birefringence of the bow-tie fibre has decreased due to the etching and the wavelength spacing of the fringe minima of the fibre loop mirror has increased.

Abstract
We report on the analysis and experimental validation of the strain sensitivity dependences of a fiber Bragg grating written in standard optical fiber when combined with fused tapers. By controlling the difference between the cross sections of the fused taper and the Bragg grating, the strain sensitivity of the Bragg wavelength can be changed by acting on the gauge length. The strain sensing characteristics of an interferometric structure formed by fabricating a fused taper in the middle of a fiber Bragg grating are also reported. (C) 2007 Optical Society of America.

Abstract
A concept of long-period-based optical fiber sensors, with broadband light illumination generated just after the sensing structure, is presented in this work. This new approach allows the interrogation in transmission of the sensing head while integrated in a reflective configuration, which means the long-period grating (LPG) sensor is seen in transmission by the optical source but in reflection by the measurement system. Also, it is shown that with this illumination layout the optical power balance is more favorable when compared with the standard configurations, allowing better sensor performances, particularly when the sensing head is located far away from the photodetection and processing unit. This is demonstrated for the case of the LPG structure applied to measure strain and using ratiometric interrogation based on the readout of the optical power reflected by two fiber Bragg gratings spectrally located in each side of the LPG resonance.

Abstract
The underground movement of water through soil and rock is an important phenomenon in Civil Engineering. Its study is made more appealing to students if small scale prototypes are used, where several layouts of soil and water in steady state/transient conditions can be studied in detail. A water tank prototype was built with a reflective optical fibre pressure sensor based on a GRIN lens and a mirror. The mirror is connected to an elastic membrane that is deformed when water pressure is applied and the lens is correctly aligned with the mirror and fixed. The distance between the mirror and the lens changes, so the reflective optical power changes as well and it is directly proportional to the water pressure inside the tank. The results obtained for water pressure up to 4 kPa for filling and emptying operations show that the sensor has a linear response for pressure changes between 1.7 kPa and 3.4 kPa with a slope of 181 mu W/kPa for filling and 191 mu W/kPa for emptying. It is also observed some hysteresis that may possibly be reduced by choosing another material for the membrane. Using this type of sensor head it is possible to monitor different pressure points in the small scale prototype using the standard OTDR (Optical Time Domain Reflectometer) equipment.