Abstract
The study of a single short length Bragg grating for sensing applications is presented. The dependences of the central wavelength, reflected optical power and spectral width of a 250 mu m length grating on strain and temperature are analyzed. The obtained results indicate the feasibility of this novel sensing head for simultaneous measurement of strain and temperature.

Abstract
Microstructured optical fibers (MOFs) have been widely studied owing to their potential for obtaining novel transmission, nonlinear and sensing characteristics. Sensing applications of MOFs cover various types of devices for measurements of different physical and specific chemical compounds in gases and liquids employing evanescent field techniques. Such fibers can also be used as active and passive elements in fiber-optic polarimetric and interferometric sensors. We present an in-line fiber modal interferometer fabricated in boron-doped highly birefringent microstructured fiber. The boron-doped region located in the middle of the core decreases the effective index of the fundamental mode and facilitates coupling between the fundamental and the first order mode. The coupling regions have the form of fiber narrowings fabricated using CO2 laser and are distant by a few millimeters. The spectral intensity at the sensor output is modulated only by intermodal interference produced by a short piece of fiber between the two coupling points. Moreover, as the fiber is highly birefringence, each pair of polarization modes produces its own intermodal fringes, which results in the contrast modulation of the overall interference signal observed at the fiber output, and provides an additional degree of freedom to measure simultaneously a pair of measurands.

Abstract
In this work the concept of long period based optical fibre sensors with the broadband light illumination generated just after the sensing structure is presented. This new approach allows the interrogation in transmission of the sensing head while integrated in a reflective configuration, which means the LPG sensor is seen in transmission by the optical source but in reflection by the measurement system. Also, it is shown that with this illumination layout the optical power balance is more favorable when compared with the standard configurations, allowing better sensor performances particularly when the sensing head is located far away from the photodetection and processing unit. This is demonstrated for the case of the LPG structure applied to measure strain and using ratiometric interrogation based on the readout of the optical power reflected by two fibre Bragg gratings spectrally located in each side of the LPG resonance.

Abstract
This work describes a large-core air-clad photonic crystal fibre-based sensing structure that is sensitive to refractive index, temperature and strain. The sensing head is based on multimodal interference, and relies on a single mode - large-core air-clad photonic crystal fibre - single mode fibre configuration. Using two distinct large-core air-clad PCF geometries it is possible to obtain an optical spectrum with two dominant loss bands, at wavelengths that have different sensitivities to physical parameters. This characteristic is explored to demonstrate a sensing head that permits the strain-temperature discrimination functionality. It is also shown the large-core air-clad photonic crystal fibre can be applied to implement a sensing head sensitive to the water refractive index changes induced by temperature variations.

Abstract
It is described a fibre optic sensor for liquid refractive index measurement based on the visibility variations of a Fabry-Perot interferometer with interfering waves generated in a short Bragg grating and in the fibre tip (Fresnel reflection) in contact with the liquid. The sensor was characterized emerging the fibre tip in distilled water with different concentrations of ethylene glycol. A linear relation was obtained, with a readout resolution of similar to 10(-3). It was also observed that the temperature direct cross sensitivity is residual.

Abstract
Optical fibre sensors for Hydrogen detection at low concentrations has become a growing research area using Palladium as an active medium. Palladium is widely used in hydrogen sensing as it show a high and selective affinity for hydrogen. This metal is capable to absorb hydrogen up to 900 times its own volume which permits that during the expansion mechanical forces are applied in the fibre modifying the optical response. Several optical fibre hydrogen sensor heads coated with Palladium are presented and compared using different working principles: interferometric, intensity and fiber grating-based sensors. These principles were applied in Fabry-Perot cavities, fibre Bragg gratings written in fibre SMF28 with etching in the cladding, multimode interferometers and fibre end micro-mirrors. Palladium thin film coatings over the fibre surface and with thicknesses from 10nm to 350nm were produced by using the sputtering RF technique. These studies were performed in a Hydrogen/Nitrogen atmosphere with Hydrogen concentrations from 0% to 4% (lower limit explosion). The Bragg grating inscribed in a fibre with reduced cladding diameter appears to be one of the best approaches for a fibre optic sensing head for Hydrogen detection. Future work will continue the investigation of other fibre optic structures with Hydrogen sensing capabilities and their application in specific field situations will be assessed.