Abstract
This work proposes a sensor that utilizes a transmission scheme for measuring glucose aqueous solutions based on surface plasmon resonance. A comparison between the performance of two sensors with similar lengths and different diameters is performed. The first sensor comprises a multimode optical fiber with a diameter of 400 µm and a 10 mm middle section of the cladding removed. The second sensor is similar, except that the fiber has a diameter of 600 µm. The sensors were evaluated for their performance in measuring glucose concentrations ranging from 0.0001 to 0.5000 g/mL. The 400 µm sensor demonstrated high sensitivity however, the sensor with a diameter of 600 µm attained a slightly higher maximum sensitivity of 322.0 nm/(g/mL).

Abstract
This paper proposes a proof of concept for a reflective fiber optic sensor based on multimode interference, designed to measure glucose concentrations in aqueous solutions that mimic the range of glucose concentrations found in human saliva. The sensor is fabricated by splicing a short section of coreless silica fiber into a standard single-mode fiber. By studying the principles of multimode interference and Self-imaging it was developed a sensing head that has a total length of 29.1 mm, approximately equal to the second self-image cycle. This sensing head allowed us to detect low concentrations of glucose (ranging from 0 to 268 mg/dl).

Abstract
The scientific community has been exploring new concepts as a result of the usage of optical fibers as absolute measurement sensors. While cross-sensitivity is a common issue with optical fiber sensors, this issue has been mitigated by simultaneous measurement techniques. But when it comes to absolute measurements, these methods have some limitations. The white light interferometer, which offers a superb solution for a range of applications, especially for absolute temperature measurement, is one of the most often used methods for absolute measurements.

Abstract
Measuring gas and liquid flow rate is paramount in various scientific and industrial applications. This work presents an optical fiber flowmeter based on a graphene oxide (GO) coated Michelson interferometer. The interferometer is fabricated using a long-period fiber grating (LPFG) followed by a GO-coated single-mode fiber (SMF). By radiating the GO coating, it experiences photothermic effect that induces local heating of the film. This results in a variation in the effective refractive index in the cladding modes, which induces a phase shift on the interferometer spectrum. When a gas flow is introduced near the coated fiber, the hot-wire region will experience a reduction in temperature proportional to the flow rate. The flowmeter exhibited a linear wavelength shift to the flow rate with an absolute sensitivity of 17.4 +/- 0.8 pm/(L.min-1) for gas flow rates between 2 and 8 L/ min. Furthermore, the dynamic response of the sensor was studied, attaining a maximum response time of 1.1 +/- 0.4 s

Abstract
In this work, an optical fiber flowmeter based on a Michelson interferometer is presented. The Michelson interferometer uses a long period fiber grating (LPFG) to couple light to the cladding modes followed by a section of a GO-coated single mode fiber (SMF). By radiating the GO thin film, it will increase its temperature changing the effective refractive index of the optical cavity of the Michelson interferometer. By placing the sensor on a gas flow, its temperature surface will decrease in a proportional manner to the flow rate. The sensor was studied in both static and dynamic dry nitrogen flow, attaining an absolute sensitivity of 17.4 ± 0.8 pm/(L.min-1) and a maximum response time of 1.1 ± 0.4 s.

Abstract
In this study, different configurations based on linear fiber lasers were proposed and experimentally demonstrated to measure the concentration of liquid solutions. Samples of paracetamol liquid solutions with different concentrations, in the range from 52.61 to 201.33 g/kg, were used as a case-study. The optical gain was provided by a commercial bidirectional Erbium-Doped Fiber Amplifier (EDFA) and the linear cavity was obtained using two commercial Fiber Bragg Gratings (FBGs). The main difference of each configuration was the coupling ratio of the optical coupler used to extract the system signal. The sensing head corresponded to a Single-Mode Fiber (SMF) tip that worked as an intensity sensor. The results reveal that, despite the optical coupler used (50:50, 60:40, 70:30 or 80:20), all the configurations reached the laser condition, however, the concentration sensing was only possible using a laser drive current near to the threshold value. The configurations using a 70:30 and an 80:20 optical coupler allowed paracetamol concentration measurements with a higher sensitivity of (-3.00 +/- 0.24) pW/(g/kg) to be performed. In terms of resolution, the highest value obtained was 1.75 g/kg, when it was extracted at 20% of the output power to the linear cavity fiber laser configuration.