Abstract
A sensing configuration for the real-time monitoring, detection, and quantification of dissolved carbon dioxide (dCO(2)) was developed for aquaculture and other applications in freshwater and saline water. A chemical sensing membrane, based on a colorimetric indicator, is combined with multimode optical fiber and a dual wavelength light-emitting diode (LED) to measure the dCO(2)-induced absorbance changes in a self-referenced ratiometric scheme. The detection and processing were achieved with an embeded solution having a mini spectrometer and microcontroller. For optrode calibration, chemical standard solutions using sodium carbonate in acid media were used. Preliminary results in a laboratory environment showed sensitivity for small added amounts of CO2 (0.25 mg.L-1). Accuracy and response time were not affected by the type of solution, while precision was affected by salinity. Calibration in freshwater showed a limit of detection (LOD) and a limit of quantification (LOQ) of 1.23 and 1.87 mg.L-1, respectively. Results in saline water (2.5%) showed a LOD and LOQ of 1.05 and 1.16 mg.L-1, respectively. Generally, performance was improved when moving from fresh to saline water. Studies on the dynamics of dissolved CO2 in a recirculating shallow raceway system (SRS+RAS) prototype showed higher precision than the tested commercial sensor. The new sensor is a compact and robust device, and unlike other sensors used in aquaculture, stirring is not required for correct and fast detection. Tests performed showed that this new sensor has a fast accurate detection as well as a strong potential for assessing dCO(2) dynamics in aquaculture applications.

Abstract
High concentration of biogenic amines (BA) is an indicator of deterioration of food and the determination of their concentration is an important method of food control. The hydrogen peroxide (H2O2) is a side product of the degradation of BAs by certain enzymes. It is presented an experimental technique grounded on chemiluminescence to measure small quantities of H2O2 with concentrations as low as 0.01%w/w up to 0.08%w/w. Luminol and cobalt hydroxide are added to hydroxyethyl cellulose to obtain an active membrane which will react with the sampling solution and the amount of total light emission is directly related to the H2O2 concentration.

Abstract

Abstract
Dissolved carbon dioxide (dCO2) evaluation is very important in many different fields. In this work, a new, integrated, colorimetric-optical fiber-based system for dCO2 monitoring in aquaculture industry was developed. The sensing chemistry is based on colorimetric changes of the used indicator—poly p-nitrophenol (pNPh)—in contact with CO2. Preliminary tests were done in a laboratory environment (calibration) and in a laboratory Recirculating Aquaculture System (RAS) with controlled CO2 injection. The results have shown the suitability of the new sensor for assessing dCO2 dynamics in RAS and its fast detection of low dCO2 concentrations in an appropriate operation range.

Abstract
Long Period Fibre Gratings (LPFGs) were fabricated by femtosecond (fs) laser direct writing in a standard single-mode fibre (SMF-28e) to measure variations in the surrounding refractive index (SRI). The sensing sensitivity of these structures was optimized with the deposition of homogeneous thin layers of titanium dioxide (TiO2) by physical vapour deposition (PVD) process. A set of LPFGs were coated with different thickness layers of TiO2, and the spectral features were monitored for different SRI solutions. The wavelength shift and the optical power variation of the LPFG minimum attenuation band were measured achieving sensitivities of similar to 570 nm/RIU at using SRI near to 1.3600 in the case of the LPFG coated with 60 nm of TiO2, a 10-fold increase over the corresponding for a bare LPFG. For SRI values higher than the cladding refractive index, a sensitivity over similar to 3000 nm/RIU was determined for 30 nm of TiO2 thick film, a region where the bare LPFGs are useless. For 30 nm of TiO2, the optical power variation follows a quasi-linear function of the SRI, with a range of similar to 10 dB. Moreover, values as high as 50 and 120 dB/RIU at 1.3200 and 1.4200, respectively, can be obtained by choosing the proper film thickness. Preliminary studies revealed that coating fs-laser direct writing LPFGs with titanium dioxide improves their performance.

Abstract
Optical microbubble resonators are among the highest sensitivity optical sensors. In the context of its application in the detection of water micro contaminants, in portable systems, their interrogation must be made by tracking the resonant wavelength peak position with the highest accuracy possible, at a reasonable cost. In this work different laser sources and scanning methods were tested and compared, aiming the development of a portable prototype. Each tunable laser source, was evaluated using a C2H2 Gas cell, which provided an absolute wavelength reference. Light transmitted through the cell was recorded using a photodetector and a software controlled feedback loop, enabling locking into selected reference peaks. Three distinct scanning methods were tested and compared for each laser source: large and short-range laser scanning and external waveform dithering, from which minimum standard deviations of 20, 0.18, and 0.07 pm, were obtained, respectively.