Abstract
In this paper, two hybrid multimode/single mode fiber Fabry-Perot (FP) cavities were compared. The cavities fabricated by chemical etching are presented as high temperature and strain sensors. In order to produce this FP cavity a single mode fiber was spliced to a graded index multimode fiber with 62.5 mu m core diameter. The Fabry-Perot cavities were tested as a high temperature sensor in the range between room temperature and 700 C and as strain sensors. A reversible shift of the interferometric peaks with temperature allowed to estimate a sensitivity of 0.75 +/- 0.03 pm/degrees C and 0.98 +/- 0.04 pm/degrees C for the sensor A and B respectively. For strain measurement sensor A demonstrated a sensitivity of 1.85 +/- 0.07 pm/mu and sensor B showed a sensitivity of 3.14 +/- 0.05 pm/mu. The sensors demonstrated the feasibility of low cost fiber optic sensors for high temperature and strain.

Abstract
We study the measurand-induced spectral shift of the photonic bandgap edge of a hollow-core photonic crystal fiber. The physical measurands considered are strain, temperature, curvature, and twist. A noticeable sensitivity to strain, temperature, and twist is observed, with a blueshift to increase strain and twist. An increase in temperature induces a redshift. On the other hand, curvature has no observable effect on the spectral position of the photonic bandgap edge. (C) 2010 Optical Society of America

Abstract
Hollow-core photonic crystal glass fibers have a high potential for gas sensing applications, since large light-gas interaction lengths can be effectively attained. Nevertheless, in order to enhance effective diffusion of gas into the hollow-core fiber, multi-coupling gaps are often needed, which raise coupling loss issues that must be evaluated prior to the development of practical systems. In this paper, a study on the coupling losses dependence on lateral and axial gap misalignment for single-mode fiber and two different types of hollow-core photonic crystal glass fibers is carried out. In addition, an experimental technique on splicing these glass fibers is also described and some results are presented showing that low splice losses can be obtained with high reproducibility. © (2010) Trans Tech Publications.

Abstract
A spatial optical filter based on a hollow-core silica tube is proposed. Because of the hollow-core dimensions, it is possible to obtain a periodical spatial filter ranging from 1200 to 1700 nm with a channel spacing of 2.64 THz. The bandwidth is approximately 5.32 nm, and the isolation loss is similar to 30 dB. The optical losses are approximately similar to 0.67 dB/mm for a wavelength of 1500 nm. The 40 mm long spatial optical filter is tested as a sensing element and subjected to different physical parameters. The spatial optical filter is wavelength sensitive to strain and temperature, while for refractive-index variations there is an optical power dependency. This fiber structure can be used as a sensing element for extreme conditions, such as in very high temperature environments, where it presents a sensitivity of 27.5 pm degrees C-1. (C) 2012 Optical Society of America

Abstract
A large-core air-clad photonic crystal fiber-based sensing structure is described, which is sensitive to refractive index. The sensing head is based on multimodal interference, and relies on a single-mode/large-core air-clad photonic crystal fiber (PCF)/single-mode fiber configuration. Using two distinct large-core air-clad PCF geometries-one for refractive index measurement and the other for temperature compensation, it was possible to implement a sensing head sensitive to refractive index changes in water as induced by temperature variations. The results indicated the high sensitivity of this sensing head to refractive index variations of water, and a resolution of 3: 4 x 10(-5) refractive index units could be achieved. (C) 2011 Optical Society of America

Abstract
A high sensitivity Fabry-Perot (FP) strain sensor based on hollow-core ring photonic crystal fiber was investigated. A low-finesse FP cavity was fabricated by splicing a section of hollow-core ring photonic crystal fiber between two standard single mode fibers. The geometry presents a low cross section area of silica enabling to achieve high strain sensitivity. Strain measurements were performed by considering the FP cavity length in a range of 1000 mu m. The total length of the strain gauge at which strain was applied was also studied for a range of 900 mm. The FP cavity length variation highly influenced the strain sensitivity, and for a length of 13 mu m a sensitivity of 15.4 pm/mu epsilon was attained. Relatively to the strain gauge length, its dependence to strain sensitivity is low. Finally, the FP cavity presented residual temperature sensitivity (similar to 0.81 pm/degrees C). (C) 2012 Optical Society of America