Abstract
This work presents a fiber cavity ring down (CRD) configuration for the measurement of strain. An optical time-domain reflectometer (OTDR) was used to send impulses down into the fiber loop cavity, inside of which a chirped fiber Bragg grating was placed to act as a strain sensing element. This technique could provide strain results with both conventional CRD-based configuration and the OTDR. The CRD configuration provided a linear response to strain applied in the range 0-2000 epsilon, and a sensitivity of 1.34 ns/epsilon was obtained. For the same operation range, the OTDR interrogation allowed obtaining a periodic behavior due to fiber Bragg grating scanning of the wavelength peaks of the multimode laser source while increasing strain. It is shown that the OTDR interrogation method provide a ring-down time response of about 8 s which is a great improvement when compared to the conventional CRD configuration (23 s). (c) 2015 Wiley Periodicals, Inc. Microwave Opt Technol Lett 57:1442-1444, 2015

Abstract
Cross-bite, as a malocclusion effect, is defined as a transversal changing of the upper dental arch, in relation to the lower arch, and may be classified as skeletal, dental or functional. As a consequence, the expansion of maxilla is an effective clinical treatment used to correct transversal maxillary discrepancy. The maxillary expansion is an ancient method used in orthodontics, for the correction of the maxillary athresia with posterior crossbite, through the opening of the midpalatal suture (disjunction), using orthodontic-orthopaedic devices. Same controversial discussion arises among the clinicians, about the effects of each orthodontic devices as also about the technique to be employed. The objective of this study was to compare the strain field induced by two different orthodontic devices, named disjunctor with and without a connecting bar, in an acrylic model jaw, using fiber Bragg grating sensors to measure the strain patterns. The orthodontic device disjunctor with the bar, in general, transmits higher forces and strain to teeth and maxillae, than with the disjunctor without bar. It was verified that the strain patterns were not symmetric between the left and the right sides as also between the posterior and anterior regions of the maxillae. For the two devices is also found that in addition a displacement in the horizontal plane, particularly in posterior teeth, also occurs a rotation corresponding to a vestibularization of the posterior teeth and their alveolar processes.

Abstract
Direct identification of cohesive laws in modes I and II of wood bonded joints is addressed by the double cantilever beam (DCB) and end-notched flexure (ENF) tests, respectively. Moreover, the development and extension of fracture process zone (FPZ) ahead of the initial crack tip, is analysed by means of digital image correlation (DIC) and embedded fibre Bragg grating (FBG) sensors. From FBG spectral response, the spectrum geometric mean is determined and the strain induced by wavelength variation employed to identify the initial and final stages of the FPZ. These stages are used to consistently define the cohesive laws in both modes I and II. Resistance-curves are determined from the compliance-based beam method (CBBM). Besides, the crack tip opening displacements (CTOD) are determined by post-processing displacement field provided by DIC around the initial crack tip. The strain energy release rate as a function of the CTOD are then determined for both mode I and mode II. The respective cohesive laws are reconstructed by numerical approximation and differentiation. It is concluded that the proposed data reduction scheme is effective to determine both the FPZ development phase and the corresponding cohesive laws of wood bonded joints in both mode I and mode II.

Abstract
This work addresses the experimental identification of mode I cohesive law of wood bonded joints. The approach combines the double cantilever beam (DCB) test with both digital image correlation (DIC) and embedded fibre Bragg grating (FBG) sensors. The spectrum geometric mean of the FBG reflected spectral response was determined, and the wavelength evolution was used to define the fracture process zone (FPZ) development phase. This evaluation allowed a consistent selection of experimental range of over which the identification procedure of mode I cohesive law is build up. Mode I crack length, Resistancecurve and cohesive law parameters are characterised and discussed. The strain energy release rate (G(I)) is determined from the P-delta curve by the compliance-based beam method (CBBM). The crack tip opening displacement (w(1)) is determined by post-processing displacements measured by DIC. The cohesive law in mode I (sigma(1)-w(1)) is then obtained by numerical differentiation of the G(1)-w(1) relationship.

Abstract
Engineering techniques used to evaluate strain-stress fields, materials' mechanical properties, and load transfer mechanisms, among others, are useful tools in the study of biomechanical applications. These engineering tools, as experimental and numerical ones, were imported to biomechanics, in particular in dental biomechanics, a few decades ago. Several experimental techniques have been used in dental biomechanics, like photoelasticity, ESPI (Electronic Speckle Pattern Interferometry), strain gages, and other kinds of transducers. However, these techniques have some limitations. For instance, photoelasticity and ESPI give the overall field pattern of the strain, showing the stress-strain concentration points. These methods cannot give an accurate measurement at all points. On the contrary, strain gages can be used to perform local measurements. However, as they use electrical resistances, their use is limited to perform in vivo measurements. Optical fiber sensors have already been used in dentistry, for diagnostic and therapeutic purposes, and in dental biomechanics studies. Lasers have also been used in clinical dentistry for a few decades. Other optical technologies, like optical coherence tomography (OCT), became suitable for dental practice and nowadays it is perhaps one that has had more development in dentristry, along with lasers.

Abstract
We describe the use of a phase-sensitive optical time domain reflectometer (phi OTDR) over an ultra-long Raman fiber laser cavity allowing fully distributed detection of vibrations over 125 km. Compared to a first-order Raman-assisted phi OTDR, this scheme shows an enhanced signal-to-noise ratio (SNR). This is due to the fact that the relative intensity noise introduced by the Raman amplification is mostly transferred to a lower frequency range, where the balanced detection implemented in the setup provides better suppression of the common-mode noise. The sensor was able to measure vibrations of up to 380 Hz (limit set by the time of flight of light pulses) in a distance of 125 km with a resolution of 10 m and an average SNR of 8 dB with no postprocessing. This implies a > 3 dB improvement in SNR over a first-order Raman-assisted setup with similar characteristics.