Abstract
Systems for wireless energy transmission (WET) are gaining prominence nowadays. This work presents a WET system based on the photo-thermoelectric effect. With an incident laser beam at lambda = 1450 nm, a temperature gradient is generated in the radial flexible thermoelectric (TE) device, with a carbon-based light collector in its center to enhance the photoheating. The three-part prototype presents a unique approach by using a radial TE device with one simple manufacturing process - screen-printing. A TE ink with a polymeric matrix of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate and doped-Poly(vinyl alcohol) with Sb-Bi-Te microparticles is developed (S similar to 33 mu VK-1 and s similar to 10.31 Sm-1), presenting mechanical and electrical stability. Regarding the device, a full electrical analysis is performed, and the influence of the light collector is investigated using thermal tests, spectrophotometry, and numerical simulations. A maximum output voltage (Vout) of similar to 16 mV and maximum power density of similar to 25 mu Wm(-2) are achieved with Plaser = 2 W. Moreover, the device's viability under extreme conditions is explored. At T similar to 180 K, a 25% increase in Vout compared to room-temperature conditions is achieved, and at low pressures (similar to 10(-6) Torr), an increase of 230% is obtained. Overall, this prototype allows the supply of energy at long distances and remote places, especially for space exploration.

Abstract
The use of graphene oxide (GO) as a saturable absorber for short pulses generation in an Erbium-doped fiber laser was studied and demonstrated. The saturable absorber consisted of a thin GO film, with a high concentration of monolayer GO flakes, spray-coated on the end face of a ferrule-connected fiber. By including the saturable absorber in the laser cavity and controlling the intra-cavity polarization, the generation of shortpulsed light was achieved under mode-locking and Q-switching operations. Under mode-locking operation, it was observed a pulse train with a fundamental repetition rate of 1.48 MHz, with a working wavelength centered at 1564.4 nm. In the Q-switch operation, a pulse train with a 12.7 kHz repetition rate and a 14.3 µs pulse duration was attained for a 230-mA pump current. Further investigation showed a linear dependence of the repetition rate with the pump power, attaining frequencies between 12.7 and 14.4 kHz. © 2023 by SCITEPRESS - Science and Technology Publications, Lda.

Abstract
The scientific community has been exploring new concepts as a result of the usage of optical fibers as absolute measurement sensors. While cross-sensitivity is a common issue with optical fiber sensors, this issue has been mitigated by simultaneous measurement techniques. But when it comes to absolute measurements, these methods have some limitations. The white light interferometer, which offers a superb solution for a range of applications, especially for absolute temperature measurement, is one of the most often used methods for absolute measurements.

Abstract
Measuring gas and liquid flow rate is paramount in various scientific and industrial applications. This work presents an optical fiber flowmeter based on a graphene oxide (GO) coated Michelson interferometer. The interferometer is fabricated using a long-period fiber grating (LPFG) followed by a GO-coated single-mode fiber (SMF). By radiating the GO coating, it experiences photothermic effect that induces local heating of the film. This results in a variation in the effective refractive index in the cladding modes, which induces a phase shift on the interferometer spectrum. When a gas flow is introduced near the coated fiber, the hot-wire region will experience a reduction in temperature proportional to the flow rate. The flowmeter exhibited a linear wavelength shift to the flow rate with an absolute sensitivity of 17.4 +/- 0.8 pm/(L.min-1) for gas flow rates between 2 and 8 L/ min. Furthermore, the dynamic response of the sensor was studied, attaining a maximum response time of 1.1 +/- 0.4 s

Abstract
This paper presents an approach to enhancing sensitivity in optical sensors by integrating self-image theory and graphene oxide coating. The sensor is specifically engineered to quantitatively assess glucose concentrations in aqueous solutions that simulate the spectrum of glucose levels typically encountered in human saliva. Prior to sensor fabrication, the theoretical self-image points were rigorously validated using Multiphysics COMSOL 6.0 software. Subsequently, the sensor was fabricated to a length corresponding to the second self-image point (29.12 mm) and coated with an 80 mu m/mL graphene oxide film using the Layer-by-Layer technique. The sensor characterization in refractive index demonstrated a wavelength sensitivity of 200 +/- 6 nm/RIU. Comparative evaluations of uncoated and graphene oxide-coated sensors applied to measure glucose in solutions ranging from 25 to 200 mg/dL showed an eightfold sensitivity improvement with one bilayer of Polyethyleneimine/graphene. The final graphene oxide-based sensor exhibited a sensitivity of 10.403 +/- 0.004 pm/(mg/dL) and demonstrated stability with a low standard deviation of 0.46 pm/min and a maximum theoretical resolution of 1.90 mg/dL.