Abstract
Low voltage actuators based on poly(vinylidene fluoride) (PVDF) with 10, 25 and 40% 1-hexyl-3-methylimidazolium chloride ([C(6)mim][Cl]) and 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C(6)mim][NTf2]) are prepared by solvent casting in order to evaluate the effect of anion size in the bending properties. Independently of the ionic liquid type and content, its presence leads to the crystallization of PVDF in the beta-phase. The addition of ionic liquid into the polymer matrix decreases significantly its degree of crystallinity and the elastic modulus. It is also confirmed the good miscibility between PVDF and IL, determined by the interaction of the CF2 groups from the PVDF chains with the imidazolium ring in the ionic liquid (IL). The AC conductivity of the composites depends both on the amount of ionic liquid content and anion size. The bending movement of the IL/PVDF composites is correlated to their degree of crystallinity, mechanical properties and ionic conductivity value and the best value of bending response (0.53%) being found for IL/PVDF composite with 40 wt of [C(6)min][Cl] at an applied voltage of 10 V square signal.

Abstract
The authors wish to make the following erratum to this paper [1]: Equations (1), (7), and (9) are incorrect and must be replaced by the following equations: [Formula presented] The authors apologize for this literal mistake, but emphasize that the content of the article is still correct, since all calculations were performed with the correct equations. The manuscript will be updated and the original will remain online on the article webpage, with a reference to this Erratum.

Abstract
The lack of penetration of light and electromagnetic radiation beyond a few meters in the ocean makes acoustics the technique of choice for data transmission, target detection and ocean sensing in general. Acoustic transducers are typically based on piezoelectric materials due to the good response at high frequencies. Depending on the application it can be built using ceramics, polymers and composite materials. In the hydrostatic mode PZT ceramics hydrophones have low performance due to the low hydrostatic piezoelectric stress value. On the other hand, PVDF have shown relatively high hydrostatic mode response. This work presents the development of a PVDF hydrophone for deep sea applications. The hydrophone was subjected to a pressure test up to 25 MPa to evaluate the response variation under high hydrostatic pressure. The results show an increase up to 6 dB sensitivity under 15 MPa pressure.

Abstract
Energy harvesting devices can increase autonomy of submersible marine sensors. However, only the water movements can be used as energy source, since neither solar or temperature gradients are available bellow surface waters. A Linear Electromagnetic Generator (LEG), in a milliwatt energy harvester, is presented. Any moving parts are in contact with water, thus avoiding biofouling problems in the harvester. In this work, a 100mm length, 60mm diameter, cylindrical LEG was designed to maximize output power, and analyzed the effects of magnets size and geometry as well as coils position, at several working conditions. Two coils were used, with an internal resistance of 130 ? in 1500 turns, together with N38-N42 magnets. A mean electrical power of 25 mW (100 mW peak) was experimental measured in the optimized configuration, in realistic conditions, which is enough to power almost any electronic low-power sensor.

Abstract
Salinity measurement in water is typically performed with conductivity sensors. However, for long-term marine deployments, loss of precision is observed, mainly due to electrode drift (oxidation and degradation occurs in the presence of water, salts and bio-fouling), which results in inaccuracy of measurements. A cost-effective, low-power, four-probe salinity sensor is presented, to accurately measure long-term deployments in oceans, rivers and lakes. The four-probe methodology overcomes many of the drift problems, and the use of low-cost stainless-steel electrodes (avoiding platinum or titanium materials) can still achieve good long-term stability, in the practical salinity scale range from 2 to 42 PSU. Low-power electronics (200 µA in sleep-mode and 1 mA in active-mode) based on a ratiometric ADC conversion, and a low-power microcontroller with non-volatile memory, complements the proposed sensor, to achieve an autonomous salinity sensor for long-term marine deployments, with autonomy above 1 year with a 1 min-1 sample rate, using a common 2400 mA x 3.7 V lithium battery.

Abstract
This work aims to study a new energy harvesting device to be anchored on the ocean floor and convert any type of currents, tides or oscillation movement into electrical energy using linear electromagnetic generators. The final application is to supply energy to a set of moored monitoring sensors that collects data and allowing the system to be energetically autonomous. The proposed setup is a spherical buoy with no external moving parts, to be more biofouling proof. The maximum output power measured for a 4 Hz movement was 9.9 mW with only one linear electromagnetic generator.