Abstract
A cost-effective (less than 20€) and low-power device is present for in situ continuous monitoring of suspended sediments (SPM) concentration in estuarine and coastal areas. The sensor uses nephelometric technique for SPM values less than 20g/L and backscatter technique for higher ones. A transmitted infrared (IR) and ultraviolet (UV) channels are used to perform the distinguish of inorganic from organic matter in the suspended particles. It is explained the design and built of the sensor as its calibration and preparation for in field tests. The sensor was deployed for one week in a small dock in the estuarine zone of Cavado river (Esposende, Portugal) where is analyzed the SPM and organic/inorganic matter change with the tidal cycles.

Abstract

Abstract
Abstract: In this work, different weight contents of as-grown carbon nanofibers (CNFs), produced by chemical vapor deposition, were melt-extruded with polypropylene (PP) and their morphologic, structure and dielectric properties examined. The morphologic analysis reveals that the CNFs are randomly distributed in the form of agglomerates within the PP matrix, whereas the structural results depicted by Raman analysis suggest that the degree of disorder of the as-received CNFs was not affected in the PP/CNF composites. The AC conductivity of PP/CNF composites at room temperature evidenced an insulator–conductor transition in the vicinity of 2 wt.%, corresponding to a remarkable rise of the dielectric permittivity up to ~ 12 at 400 Hz, with respect to the neat PP (~ 2.5). Accordingly, the AC conductivity and dielectric permittivity of PP/CNF 2 wt.% composites were evaluated by using power laws and discussed in the framework of the intercluster polarization model. Finally, the complex impedance and Nyquist plots of the PP/CNF composites are analyzed by using equivalent circuit models, consisting of a constant phase element (CPE). The analysis gathered in here aims at contributing to the better understanding of the enhanced dielectric properties of low-conducting polymer composites filled with carbon nanofibers. Graphic abstract: [Figure not available: see fulltext.]. © 2021, The Author(s), under exclusive licence to EDP Sciences, SIF and Springer-Verlag GmbH Germany, part of Springer Nature.

Abstract
The advanced and widespread use of microfluidic devices, which are usually fabricated in polydimethylsiloxane (PDMS), requires the integration of many sensors, always compatible with microfluidic fabrication processes. Moreover, current limitations of the existing optical and electrochemical oxygen sensors regarding long-term stability due to sensor degradation, biofouling, fabrication processes and cost have led to the development of new approaches. Thus, this manuscript reports the development, fabrication and characterization of a low-cost and highly sensitive dissolved oxygen optical sensor based on a membrane of PDMS doped with platinum octaethylporphyrin (PtOEP) film, fabricated using standard microfluidic materials and processes. The excellent mechanical and chemical properties (high permeability to oxygen, anti-biofouling characteristics) of PDMS result in membranes with superior sensitivity compared with other matrix materials. The wide use of PtOEP in sensing applications, due to its advantage of being easily synthesized using microtechnologies, its strong phosphorescence at room temperature with a quantum yield close to 50%, its excellent Strokes Shift as well as its relatively long lifetime (75 mu s), provide the suitable conditions for the development of a miniaturized luminescence optical oxygen sensor allowing long-term applications. The influence of the PDMS film thickness (0.1-2.5 mm) and the PtOEP concentration (363, 545, 727 ppm) in luminescent properties are presented. This enables to achieve low detection levels in a gas media range from 0.5% up to 20%, and in liquid media from 0.5 mg/L up to 3.3 mg/L at 1 atm, 25 degrees C. As a result, we propose a simple and cost-effective system based on a LED membrane photodiode system to detect low oxygen concentrations for in situ applications.

Abstract
A cost-effective optical instrument for continuous in-situ monitoring applications is presented. With a production cost in raw materials of 38 Euro, a power consumption of 300 mu A in sleep mode and 100 mA in active mode (5 ms reading), and a capacity to monitor turbidity and sedimentary displacement at eight different depths in the water column, the sensor was developed for sediment monitoring in coastal areas. Due to the extent and dynamics of the processes involved in these areas, observations require a wide spatial and temporal resolution. Each of the eight monitoring nodes uses one infrared backscatter channel, to estimate turbidity and sediment concentration, and one ultraviolet with one infrared transmitted light channels to distinguish organic/inorganic composition of the suspended material load. An in-lab calibration was conducted, using formazine to correlate turbidity with the electronic outputs of the instrument. An analysis of the influence of external light sources and correction techniques were performed. Moreover, an in-lab experiment was conducted to study the behaviour of the sensor-to-sediment transport, wash load and sediment accumulation. The device was deployed, with a water level sensor, in an estuarine area with high sediment dynamics. The monitoring data were analysed, showing the potential of the device to continuously monitor turbidity, sediment processes, and distinguish between organic and inorganic matter, at the different depths in the water column.

Abstract
A cost-effective optical sensor for continuous in-situ monitoring of turbidity and suspended particulate matter concentration (SPM), with a production cost in raw materials less than 20 (sic), is presented for marine or fluvial applications. The sensor uses an infrared LED and three photodetectors with three different positions related to the light source-135 degrees, 90 degrees and 0 degrees-resulting in three different types of light detection: backscattering, nephelometry and transmitted light, respectively. This design allows monitoring in any type of environment, offering a wide dynamic range and accuracy for low and high turbidity or SPM values. An ultraviolet emitter-receiver pair is also used to differentiate organic and inorganic matter through the differences in absorption at different wavelengths. The optical transducers are built in a watertight structure with a radial configuration where a printed circuit board with the electronic signal coupling is assembled. An in-lab calibration of the sensor was made to establish a relation between suspended particulate matter (SPM) or the turbidity (NTU) to the photodetectors' electrical output value in Volts. Two di fferent sizes of seashore sand were used (180 mu m and 350 mu m) to evaluate the particle size susceptibility. The sensor was tested in a fluvial environment to evaluate SPM change during sediment transport caused by rain, and a real test of 22 days continuous in-situ monitoring was realized to evaluate its performance in a tidal area. The monitoring results were analysed, showing the SPM change during tidal cycles as well as the influence of the external light and biofouling problems.